RAIN RFID reader using ST25RU3993 & STM32WL

Hi there... Actually I did the fingerprint identification before but I didn't do RFID, if that's acceptable to you that I do everything while the project is going it will be very Ok.. I have been designing embedded systems since 2013, and for the PCB, I'll do it using Eagle designer. I hope we get to chat to discuss more.. Kind regards

Best RFID Design Expert at your doorstep! Dear Client, I can complete design of the RAIN RFID reader using ST25RU3993 & STM32WL We couldn’t stop ourselves from bidding after going through the description as they are an exact match with our skill set and experience. We have experience in RFID reader based PCB design and know all the intricacies required to get the job done with perfection. With more than 15 Years of experience in PCB Design and Circuit Design in Altium, We can ensure you best quality work and before time delivery. Following is a brief list of expertise that we are carrying: 1. IOT products development 2. Microcontrollers based circuit design – STM32, STM8S etc 3. Smart Products like Smart watch - GSM/GPRS/GPS etc 4. Wireless Products - BLE/WiFi- ESP32/ESP8266/NRF24L01 5. Low Power Battery Products design – Rechargeable and Non chargeable 6. Power Electronics – Buck, Boost, Flyback etc 7. BOM, RFID reader, ST25RU3993, STM32WL Please answer the following questions: 1 What are your future plans with this project? 2. Are there any specific market standards like CISPER you are aiming? 3. What will be ambient temperature of this product? 4. Are there any other specific requirements besides the ones you mentioned Let’s have a quick discussion for 5 mins where we would formulate a plan of action of how we shall take this project to the horizons of success. Regards Avi Tech Experts Quality is never an Accident

Hello, thank you for your job posting. I read your description about--RAIN RFID READER I am a senior electrical engineer. I have plenty of experience in firmware development and micro-controller developments. I can write the firmware based on Arduino, Raspberry Pi, Pic, Atmega, FPGA, ARM, DSP, PLC and so on. And I can design the circuit by the Altium, Eagle, KiCAD, Allegro & OrCAD, PADs. I provide the services - Gerber files, Netlist generation, BOM generation and 3D Models of PCAD and ECAD. I am also good at AutoCAD, Solidworks. And I can simulate all circuits with Proteus, LT-spice, Matlab, Simulink, Multisim, and Labview as well. Due to my experience in firmware development, I will bring you the perfect result in time with high quality. I will also give you a detailed explanation of the process. Looking forward to hearing from you soon Thanks

Hi. I have read your project description carefully, so I am very interesting in this project. I have good experience in RFID reader design. If you need, I will show my previous working for RFID. Best regards, Andrii.

Hi dear client I read your proposal carefully and I am whom you are looking for. I am an expert in circuit design and have rich experience in this field. Also I am an firmware developer and I am familiar with STM32 series. In the past I have realized the drone control using stm32f407. Recently, I have designed high light led driver using max25612. There I controlled the brightness of led using remote control with stm32f103. So as far as I am concerned, you will get good results working with me. Thanks for your attention Warm Regards

Hi Employer! I am Matlab developer and have been working since last 6 years. I have checkout the description. I am waiting for you over the chat. Thank you!

Hi I am very interested in your project. In my past projects i have designed electronic circuits with stm32. I can complete your project with skills and experiences. Please contact me.

Dear Client, I can design of RAIN RFID reader using ST25RU3993 & STM32WL, I have read and understood your requirements and could do it for you in the least time and utmost superior quality. I have experience in RAIN RFID reader and could design it for you as per your requirements. I am having more than 15 years of experience in PCB Design, Circuit Design, Circuit simulation, IOT products development and building electronic products. The expertise of mine is in the following fields: 1. Wireless Products – BLE, Wifi, NFC, LoRa etc 2. Power Electronics- Buck, Boost, Flyback, Half Bridge etc 3. IOT sensors interfacing – Pressure, Temperature, Moisture, PH etc. 4. Microcontrollers- ESP32, STM32, STM8S, RL78 etc. 5. GSM, GPS, GPRS 6. BOM, RFID reader, ST25RU3993, STM32WL After reading your project details, I have certain queries and suggestions: 1. What is the application of this product? 2. What will be ambient temperature of this product? 3. What are the mechanical constraints to be taken care of? 4. What are the standards that the product would be complying to? 5. What are the user protections required for this project? Please try to answer these questions based on which I would be providing free of cost consultation. I am new to this site but I am an expert in electronics product development. Please message me so that I can formulate a success plan for this project. Waiting for your reply, Regards Hari Mohan Engineering for one is a magic for others

Hello, Greetings! I am an Electrical Engineer with specialization in PCB Layout, Electrical Engineering, Circuit Design, Electronics and Product Design. I have high proficiency in Electrical Engineering, HVAC, LTE system model, Thermal system design, FPGA, Verilog / VHDL, Matlab/ Simulink, Microcontroller, Modeling, optimization, simulation of building energy systems: PCB Layout, Arduino and have been working on Industrial Automatics and Electronics. My fields of interest are Schematic design, Prototyping, PCB Design, Development of Electronic systems, Firmware and Software development. I would love to discuss this project with you and meet your exact requirements. I am confident I can provide you with top-notch materials that will fit your needs. Once you share the project, I will have a look & confirm if I can do it. I’m honest, creative and a unique person to acarry out your tasks given to me. Leaving your project with me is a privilege; I will make sure that the project is done in a perfect way and do my very best until you are satisfied. I pride my work on being professional, of the highest quality and always delivered on time. Thank you #RAIN RFID reader using ST25RU3993 & STM32WL

Hello I have more than 15 years of experience in the embedded systems design and pcb design and electronics systems design So let's discuss your project in chat

Hi, I have already programmed STM32 MCU like STM32F4Discovery and STM32F030-Discovery using STM32CubeMX and IAR EWARM. My name is Jaspreet & I'm part of larger embedded hardware and firmware development team. Please share us more details about your project so we can able to provide you proposal with desired solutions. Looking forward to hearing from you soon! Thanks

Hello, we saw your project. we understand your project. we can build your RAIN RFID reader using ST25RU3993 & STM32WL you can contect me without any hasitaion. thank you. Shabbir Hussain.

Hello, I’m Reinerio a Computer Engineer living in South East United States, currently working in the Aircraft Flight Simulator industry. Experienced with PCB and schematic design, PCB manufacturing as well as firmware programming. Currently I’m seeking projects in the PCB design field, with potentially building new relationships. Looking at your job posting here are some questions I have: - Is there a circuit design already? - If the circuit is designed what are the number of components in the system? - Any pcb shape or size requirements? - Any pcb manufacturing requirements? - Does the design need to be designed in a desired design tool? All in all hope to hear back from you. My rate is not fixed, I’m flexible and open to your budget.