Luis I. Profile

EXPLORE

0.0

(0 reviews)

You're now following

Error following user.

This user does not allow users to follow them.

You are already following this user.

Your membership plan only allows 0 follows. Upgrade here.

Successfully unfollowed

Error unfollowing user.

You have successfully recommended

Error recommending user.

Something went wrong. Please refresh the page and try again.

Email successfully verified.

$40 USD / hour

caracas,

venezuela

$40 USD / hour

It's currently 12:36 AM here

Joined January 21, 2016

0 Recommendations

Luis I.

@tambirita

0.0

(0 reviews)

0.0

$40 USD / hour

caracas,

venezuela

$40 USD / hour

N/A

Jobs Completed

N/A

On Budget

N/A

On Time

N/A

Repeat Hire Rate

Mechanical Engineering Consultant

Highly skilled in mechanical engineering related to rotating machinery. Highly skilled in PC technology and softwares, Windows System and Office applications. Enjoy mathematics and writing. Full profile and recommendations at Linkedin Luis Infante Caracas Venezuela.

See all Trainers in Venezuela

Contact Luis I. about your job

Portfolio

2453816

Luis Infante´s Resume

2453779

Wrong Sizing of a Recip Compressor in Oil & Gas Service

2453770

A Wear Map for Recip Compressors. CompressorTech2 Magazine.

2453816

Luis Infante´s Resume

2453779

Wrong Sizing of a Recip Compressor in Oil & Gas Service

2453770

A Wear Map for Recip Compressors. CompressorTech2 Magazine.

Reviews

Changes saved

No reviews to see here!

Experience

Ingeniería Turbodina, C.A.

Jul 1997 - Present

Rotating Equipment Engineering and Consulting for the Energy Industry. Turbo & reciprocating machinery R&D, education, engineering, troubleshooting and dynamic analyses. To asses reliability and efficiency affairs on rotating machinery in the energy industry. Training programs in centrifugal and reciprocating compressors. Specialties: Reliability Engineering for the Rotating Equipment Rotordynamic of Turbomachiinery Thermodynamic Performance of Compressors

Intevep, S.A., affiliate of Petroleos de Venezuela PDVSA

Jul 1989 - Jun 1997 (7 years, 11 months)

Research and Technical Support Center for Petroleos de Venezuela. Turbo and reciprocating machinery troubleshooting and technological issues using computer codes for rotordynamic of turbomachinery. Modeling & dynamic simulations, field assistance, failure investigations, performance optimization analyses, diagnostic and remedy, Vibration analyses, mechanical audits, Retrofit & upgrading, design audits, specifications and selection,

Metalmechanic and Plastic Industries

Mar 1979 - May 1997 (18 years, 2 months)

Production and maintenance engineering and management. Group leader. Maintenance, repair & design of precision mechanic for rotating machinery. Detailed maintenance programs, production and materials controls, performance evaluation programs. -Plant engineering for high speed, high precision presses. -Designed of a forced ventilation system. -Application of advanced maintenance tools and techniques. -Management of plant personel and machinery. -Detailed engineering for fire fighting dry pipe

Education

Bachelor of Science in Mechanical Engineering

Universidad Simón Bolívar,

Venezuela

1973 - 1978

(5 years)

Qualifications

Center for the Virtual Online Studies

2014

Compose and implement online training courses using Moodle platform. 250 hours diplomate

Dynalco Controls Corp, Crane Grupo, USA

2010

Electronic Monitoring and Analysis of Reciprocating Machinery

Publications

Dense Rotor Elastomasic Modelling of a GE 1SU3 Steam Turbine Rotor

Intevep (Petroleos de Venezuela) Specialized Technical Service Report INT-TEIG-0059,95

Unique vibration pattern lead to the rotordynamic analysis of this steam turbine rotor. A non-synchronous vibration was raising the overall level to alarm. This report contains the development of the mathematical model, calibration and validation.

Mass Elastic Modeling of the NP BCL356 Centrifugal Compressor Rotor

Intevep (Petroleos de Venezuela) Specialized Technical Service Report INT-TEIG-0059,95

A stability rotordynamic analysis for this natural gas booster compressor required this mass elasic modelling.

Plasmae Coating of Steel Surfaces

1st PDVSA Maintenance Conference 1990

Plasmae Coating of Steel Surfaces and its applications to produce wear-resistant materials.

Mathematical Modelling and Calibration of a Gas Turbine Rotor

Rotating Machinery and Controls ROMAC Labs, University of Virginia, USA

Mathematical Modelling and Calibration of a Gas Turbine Rotor in Offshore Application for Rotordynamic Analysis Purposes. The ulterior objective was to implement a field balancing procedure.

Technical Analysis of a Reciprocating Compressor Station

XII Gas Symposium. Gas Processors Association. Venezuelan Chapter

This paper describes the technological options available to repower and optimize elder integral low speed engine/compressor sets existing in Venezuela.

Rotordynamic Applied to Turbomachinery Maintenance

II Turbomachinery Maintenance Workshop. Petróleos de Venezuela, S.A.

Rotordynamic Applied to Turbomachinery Maintenance

Mass-Elastic Modelling of a Gas Turbine Rotor

VI Latin-American Turbomachinery Congress - Ciateq Mexico

A mass-ellastic modelling of an old gas turbine rotor holds 98% accuracy as per a bump test and field readings. This was the begining of a field balancing analysis done over a resonant machine.

Rotordynamic Audit for a High Performance Turbopump in a Water Injection Service

Simon Bolivar University

A rotordynamic audit was performed on this high pressure water pump. Sophisticated computatinal rotordynamic codes were used in order to simulate the dynamic performance of the rotor which physical model is shown below. According to these results Pump P170 malfunctioning is the combination of resonance + dynamic instability. These are the most probable causes of the failure ocurred on...

WRONG SIZING OF A RECIP COMPRESSOR IN OIL AND GAS SERVICE

2014 Windrock Conference - Dover Corporation

What happens when a wrongly sized multistage compressor is applied in a gas field?. This is the story of a two stage compressor in a natural gas application needding only one stage. There are two objectives for this lecture: 1.- to see the effect of wrong cylinder sizes and 2.- to present novel graphical tools for the diagnostic and optimization of reciprocating compressors.

A Wear Map For Reciprocating Compressor Performance

Compressor Tech 2 Magazine - Diesel and Gas Turbine Publications Group

Reciprocating compressors in oil & gas applications are subject to stringent operating conditions that may lead to accelerated wear on the pressure seals. It also applies to combustion engines. Compressor performance maps are a graphic model of the thermodynamic behaviour of the machine, usually in “as new” condition, and methodologies to graphically account for wear in such maps are not abundant in the energy industry. Some operators of recip compressors in remote areas or areas with little

Training Manual on Reciprocating Compressors

CEPET

Section 1: Technology Principles. PV Diagram Section 2: Configuration, Design, and Construction. Section 3: Sizing, Performance and Control. Special Types. Section 4: Diagnostic and Optimization. Perf. Softwares Section 5: Valve Dynamic Performance. Section 6: Leakage Detection using Electronic Analyzers.

Training Manual on Centrifugal Compressors

CIED

Section 1: Technology Principles. Section 2: Centrifugal Compressor Stations Section 3:Configuration, Design and Construction. Section 4: Sizing, Performance and Control. Special Types. Section 5: Introduction to Rotordynamic of Turbomachinery.