Eagle arduino jobs

I have a code that works perfect with SIM5300E, I am looking for someone to modify it and makes work with SIM7000G… I have tested the GPRS registration with SIM7000G, it works almost fine; but it needs extra work to make it more reliable… I am using TinyGSM libraries and other Arduino libraries… My board has STM32 and I am using platformIO with Arduino environment to build my code…

we need to to generate a firmware wifi / bluetooth /cloud services for mobile APP. The firmware has to be indipendent from Arduino applications . Free rtos . Eclipse

I have a linier actuator with optical feedback and pwm control. The goal: To extend and retract between two encoder points user definable in the code. Homing on powerup required. Single momentary button (use a counter for extend and retract?) Details Upon extending the actuator will stop at a defined point with a timed delay, then continues to extend to the final encoder count stop point. When it gets close to the stopping point the actuator must slow for a soft stop. Pressing the button a second time will retract the actuator to a final retracted encoder point, soft stopping as well.

I have a sketch which I would like adapted to work with a new LCD Keypad Screen. Please note, new buttons on screen keypad has an additional button (select) which I would like to now use. // New Screen //

Please Sign Up or Login to see details.

Using Eagle through Fusion 360

Hello, I need to develop a code for an esp8266 project in which = Read the IR sensor and when active, start the servo motor, when inactive, return to the starting position. (During each status, trigger an LED as well) If the ultrasound is at a distance of 8 cm, it is in a condition to check if the load cell is above 4 kg and if so, activate a led. Check if the weight is still ab...inactive, return to the starting position. (During each status, trigger an LED as well) If the ultrasound is at a distance of 8 cm, it is in a condition to check if the load cell is above 4 kg and if so, activate a led. Check if the weight is still above 4kg after 5 days, if so, activate an LED. Its similiar with this project =

Code need to work on Arduino IDE with espressif/arduino-esp32 1.0.6 I need to detect a very fast pulse end moment (10-15ms lenght) but since ESP32 takes +200ms to start up, it's must be done from wake stubs 1. Esp32 it's in deep sleep or hibernation mode 2. HIGH pulse interrupt and wake up 3. Wake stub looking for LOW/Falling 4. Wake stub detect LOW/Falling , take the time into variable and wake up as normal 5. Normal operation, print how many microseconds elapesed from LOW time Note: Your stub code must be boot up in less 10ms, otherwise it will not be able to capture the moment from HIGH to LOW Use what ever gpio number for interrupt (DEVKIT-C) Image included for better understanding

Hello there! I need someone to help me with a Nextion+Arduino project that I am working on. What I want you to do is to check the files that I have already made using Nextion Editor and Arduino to talk to each other. I'd like you to check them, improve them in terms of looks, operation and help me with what's undone. Basic idea is we have a display and Arduino and we want them to talk to each other all time and make the changes on Arduino side, I also have an I2C based battery fuel gauge IC so I'd like you to help me to track it's SOC as well. If you are someone who has worked with Nextion Displays and can do this, kindly bid. I'd prefer it if you have the display at your end and can test the firmware on Arduino and test the HM...

...the Wifi has been set, the board shall remain connected to the chosen wifi network, and if the connection is lost, it should be able to try connecting again at regular intervals until the connection is restored - If, for some reason, the board freezes or goes idle, it has to be able to reset by itself, looking again for the connection Additional conditions: - The code must be uploaded using the Arduino IDE - Provide in advance the list of necessary libraries (if any) - The code must open the possibility to develop the code further using sensors and making HTTP calls over the internet. - indicate if buttons must be introduced in the project (and how many) to reset or access the wifi configuration page (if necessary - better if it can be avoided). Please ask questions if you want...

ipk: We are in the final stage of development and there are few issues which are required to be resolved, for this we are looking for a python developer who had prior experience working in IoT, lora and mqtt service, Problem Statement 1- We are able to send the command by manually pressing button from...device in aws and then it will be sent to the device and that schedule will be saved to run everyday until any change made in those times lots in the application, Action point :- Schedule the execution of function on daily basis, while getting time slots from app once and — function should run everyday until there is change from the app, 2- Integration of physical buttons with either with Arduino or rugged board, which will execute a function when a button is pressed...

Step 1 Create a schematic diagram. You may create your schematic in either Eagle or PADS Logic. Step 2: Import the schematic diagram into PADS Layout. Step 3: Create the Gerber files for manufacturing the board You need to send the following: bottom layer, top layer, outline, and drill. Include the board file as well. The extension changes depending on the software. Pad Stack 30 mils Clearance 14 mils Trace Width Max: 180 mils Min: 18 mils •pcb design must meet the following drill bit guidelines: Function Size (mm) Size (mils) Trace 0.5 20 Trace 1.00 39 Trace 2.00 79 Drill Hole 0.5 19.7 Drill Hole 0.6 23.6 Drill Hole 0.7 27.6 Drill Hole 0.8 31.5 Drill Hole 0.9 35.4 Drill Hole 1.5 59.1 • Only PCBs from PADS are supported. Use only the drill size specifications listed...

Program an arduino mega on a simple application, 2 start buttons and activate 2 valves with a timer.

we need to to generate a firmware wifi / bluetooth /cloud services for mobile APP. The firmware has to be indipendent from Arduino applications . Free rtos . Eclipse

...bespoke property developments, tapware & bathware, door hardware and maybe mens clothing in future. We would like a modern minimalistic/futuristic logo that is unique but at the same time easy to read at a first glance. It has to be clean and representative of what we offer. We would like the wording to be a logo as well as a symbol logo to represent Avagano, a minimalistic Lion's head or an eagle. Black and white logo but one that will also look good in other colours i.e Gold, brushed brass etc. References: See attached & links below -

we need to to generate a firmware wifi / bluetooth /cloud services for mobile APP. The firmware has to be indipendent from Arduino applications . Free rtos . Eclipse

A closed path is to be followed. For example, A White, Paint filled Shape :: Square , Rectangle or a Circle drawn on floor. All captured Images are to be stitched simultaneously to form a shape of path traced. Simple GUI with start , stop and a 2 picture boxes to display live Image and real time stitched Image of path . Any practical issues at the time of trials must be supported through Any desk or Team Viewer. Stitched Image to zoom in or out depending on number of pictures snapped. Any doubts, Please ask before bidding!!

I have a sketch which I would like adapted to work with a new LCD Keypad Screen. Please note, new buttons on screen keypad has an additional button (select) which I would like to now use. //Screen//

Hi i need help with a GRBL CNC and programming the arduino i cant seem to figure it out.

Looking for a PCB layout person who used Eagle. The project has around 70 parts ICs VQFN, TSSOP, 0805, 0603 sizes. The key element is the USB charger bq25606. PCB material is FR4 74x85 mm, 62 mil sickness with a custom shape. It is a hole for a special coil 28x24.5 mm. The number of layers is 4 (or 2). We will provide details for the right candidate. Please, quote (time-budget) for the immediate start this project.

Looking for a PCB layout person who used Eagle. The project has around 70 parts ICs VQFN, TSSOP, 0805, 0603 sizes. The key element is the USB charger bq25606. PCB material is FR4 74x85 mm, 62 mil sickness with a custom shape. It is a hole for a special coil 28x24.5 mm. The number of layers is 4 (or 2). We will provide details for the right candidate. Please, quote (time-budget) for the immediate start this project.

I have a arduino mega code for a fingerprint based voting system , I need to interface the arduino with wifi module ESP01 and send the fingerprint data over wifi to a thingspeak channel. I need help with the ESP01 and thingspeak part.

I need a very simple 3D CAD design for 3D-printing a component for an Arduino-based project.

the project involves writing code to store and send lat & lng data via MQTT

Hi! I’d like a logo for my new company called “toots and talons” it’s a female directed brand and I’d like the logo to be a eagle like claw clutching a human foot.

We are starting a private school and need a new logo. The school will be called "White Mountain Christian Academy". Our logo will include an eagle with mountains. We would like the colors to be emerald green and gold/yellow. I have attached some examples of similar logos as well as an eagle design we like. ****This logo must****: 1. Include the text White Mountain Christian Academy 2. Include an eagle and mountains 3. Include emerald green and gold/yellow colors. We look forward to seeing what you can create.

Our project is contactless dustbin(AM Dustbin Product) which works on Ardino.

I made an ESP32 receiver-webserver program (ESP-now protocol in Arduino IDE) but what is missing from my code is the following: I want when we make a refresh on the receiver's webpage the data to be preserved (imagine that 10 senders for example send each of them just a string as their own id for being recognized by the receiver and a char message like "free" or "duty" which make the corresponding region-square for the particular sender green (free) or red (duty) on receiver's webpage. What now happens is: If I refresh the page all the squares start from green. I thought as a solution: the senders to send every for example 30sec the last message that they have sent but that means the senders all the time are awaken up (via timer) so as to send again the...

Looking to set up a DC motor speed control with a 128 X 32 OLED 0 - 100% bar graph using a rotary encoder switch. Arduino Beetle (Leonardo) Rotary switch encoder; Push ON/OFF, rotate clockwise ti increase speed (counterclockwise to decrease). 3 inputs. OLED, 128X32, SDL/SDA 2 outputs. LED, Green, 1 output, HIGH when on. Mosfet, NPN, 1 output. If you have any questions please let me know...

Hello, Everyone. I am looking for a PCB designer. this PCB design must be done on Eagle. If you have experience with PCB design and Eagle, Please send me proposal. Thanks.

Looking to set up a DC motor speed control with a 138 X 32 OLED 0 - 100% bar graph using a rotary encoder switch. Arduino Beetle (Leonardo) Rotary switch encoder; Push ON/OFF, rotate clockwise ti increase speed (counterclockwise to decrease). 4 inputs. OLED, 138X32, SDL/SDA 4 outputs. LED, Green, 2 output, HIGH when on...

Looking to set up a DC motor speed control with a 128 X 32 OLED 0 - 100% bar graph using a rotary encoder switch. Arduino Beetle (Leonardo) Rotary switch encoder; Push ON/OFF, rotate clockwise ti increase speed (counterclockwise to decrease). 3 inputs. OLED, 128X32, SDL/SDA 2 outputs. LED, Green, 1 output, HIGH when on.

...The rich cpu is ATSAMD21G18, 32-Bit ARM® Cortex® M0 + used on the Arduino Zero or Arduino MKR zero board. The development environment is Arduino IDE. The SD card is up to 32GB and includes the library #include <SD.h> Fat32 Audio input can be selected from depending on the setting of a GPIO pin (A3): LOW = A0 analog input, 12Bit sampling HIGH = stereo or mono I2S input from digital microphone sampling up to 44Mhz 16 bit Start audio recording from Gpio (4) Pull up low and stop from Gpo (4) High. Audio file format: .wav Incremental filename RTC timestamp date: the time is acquired from the RTC timestamp and the file takes the mone from the actual recording time. Required: release of .ino source code for Arduino ide development environment and rela...

Hello ,we have to make automatic load controller and sharing system project with the help of ardiuno programming. Automatic load controller and sharing system demo video link - In this video you will see the project and same programming we will required for over project those how will make this type of programming in arduino dm fast.

Hi, We have already created a prototype with an ESP32 WROOM from AZ-Delivery + HX711 Loadcell + LCD + 2 Input Buttons with proven Sourcode for ESP32 and the corespondening PWA-BLE Application. Now I want to create PCB layout to build 10 Prototypes. We just want have everything integratet on a small PCB (without Pinheader from Prototyp...Pinout 1x 5V Pinout for HX711 1x 2x16 LCD Display Optional - Connector for LiPo (charging trough Micro USB-B Socket) - I2C Display - Microswitch for Programming (beside the USB-B Socket, accesibel trough pin-hole) The PCB should not exted the dimesion 5x10cm. I need complete files for PCB etching and assembly (BOM, Gerber, Schematics) EasyEDA would be great if possible. However couldbe in Eagle or any other Software. Thank you for your Bi...

...actuator. The motor should stop and steering centred when joystick released. It should have a 6mm sprocket with 11 teeth and be brushless I would need a battery level indicator and charging point. Key to turn on/off A kill switch on remote controller and top of train to stop all functions. You should provide simple instructions/drawings on how to connect the parts. From my research I believe an arduino would be used and would need to be programmed. I would need support to do this. Your part of the project is to identify parts and how they connect to work. I would like advice on which motor to buy and comparison prices it needs to brake. The instructions/communication should be in good English. I would not allow access to my computer. I would carry out the work in my spare tim...

I need a logo for my company, Freedom Defense. I'd like it to have a patriotic feel and a red/white/blue color scheme. I'd like a simple design that would also look good in just black and white. Our company goal is to provide firearm safety instruction for community members who are looking to protect their co...Defense. I'd like it to have a patriotic feel and a red/white/blue color scheme. I'd like a simple design that would also look good in just black and white. Our company goal is to provide firearm safety instruction for community members who are looking to protect their constitutional freedoms and want to be prepared to defend their community and families. I was thinking of having a shield and an eagle as part of the design. The firearm part could b...

Hi there , I have gone through the detail and and after discussing , I believe I am quite capable of doing this job within the time frame in the budget mention . I hope you will find me helpful for this project and for your similar project in future

Hi i'm looking for help for my next project. I´m working on a "board game" that work with 3 electronic dice. I see a similar project in arduino webpage ( ) but i need to connect to a smartphone and a special reader. Also, i need to add a lipo battery and wireless charger.

need a logo with an eagle on it with the company name National Mining & Civil Solutions format will need to .AI IT MUST HAVE AN EAGLE ON IT

I am having problems with my relay modules when a load is connected the relay does random things, when there is no load the relay behave correctly, I am using the optocoupler as well

Help me "translate" this library: from Arduino Due to ESP32 I have few Tesla batteries with the integrated BMS, also the connectors, etc, so I can test the setup in real time. However, I do not have the know-how to port this library to the ESP32. I would need most importantly at least the following functionality: - read each "cell" voltage from the battery module (7S) - read the temperature - read the fault codes (if any) - start/stop the balancing Please read the description on the github page, also there are several hints here: Thanks! best regards,

Looking developer for a project. Lets say that i want a traffic light signal in LED panel format (64cmx32cm). Hardware/panel will receive inputs by rs232/485 comm. Will display received simple words or word pile (by rs232) on panel in red or green during certain seconds. Accept arduino, rapsberry or other solutions.

Project Scope: Function Description: Breakout/control board with Arduino Nano socket and two stepper motor drivers: TMC5160_HV Input Voltage: Motor voltage: ~42VDC Input signals: For each stepper driver: Step pin, Dir pin, Sleep pin and GND. Output: 2x 4 pins connectors for stepper motors. General requirement: Project requirement: Your bitbucket email account will be added to a forked version of followcamsolutions tmc5160_breakout base project. Project have to be developed with usage of GIT, commits to be pushed to account. All parts used, have to be in stock at All symbols, footprints, 3d step files, to be stored in project_lib. (Project have to work on a clean installed kicad version without any libraries installed) 3D step file required for

Hi, I need to build a tiny mouse-like controler for smartphone (android, if posible IOS too) based on a smd joystick, 2 smd buttons and a controller (Bluefruit EZ-Key, PRJC, Arduino or other). The final tool must allow to smoothly emulate most of the functions of the touchscreen of the smartphone (move left-right / updown, left click, right click, scroll up/down, scroll click...) The bluetooth connexion must be easy even for anyone The final goal is to wake up the connected smartphone, log-in, open and control the camera app

I need to make a single/multiplayer simon memory game, using dome push buttons, lcd display, buzzer, led strip I have the code written but its around 50% done, so i would like some help finishing it??

Scope of the project is to power two seperate PWM motors via CAN BUS. We will need to filter and read only two specific CAN ID's, and depending on the CAN value our logic will drive two separate PWM motors. The CAN data will need to be converted from Hex to Integer and then to PWM value based. Using STM32 controller and Arduino IDE. Utilizing J1913 protocol Must be located in USA and sign NDA agreement.

I need an application in VB.net which can receive data from my arduino (sending data via BLE 5.0) I have a BLE 5.0 dongle on my PC and my arduino (Seeed BLE Sense) is sending data. So this is not the about othe old Bluetooth connection (which I can do myself) . I need application for BLE 5.0 .

Please Sign Up or Login to see details.

We have programmed lights to turn on and off in our showroom with Arduino MEGA 2560. We need someone to remote into our desktop that is connected via USB 2.0 to the Arduino boards. The contractor that did this project for us no longer does this type of work, so we are trying to hire someone new we can have fix current issues, and can be used for future maintenance work (when we change lights in our showroom we need assistance in changing the icons in the GUI). I would like to set up a video call with whoever we hire, so I can explain the overall situation and how it is set up to the best of my knowledge. As far as the arduino software, and how the GUI is set up and how all of it ties together, we are not experts in this. That is why we need your help!